MODEL & MINIATURE AIRCRAFT FLIGHT CONTROL SYSTEM
sa MODEL & MINIATURE AIRCRAFT: CONTROL LINE CONTROL SYSTEM
xx MODEL & MINIATURE AIRCRAFT
Template for making tidy control surface hinges from sewing thread. AERO MODELLER #680 Sep 1992 (v.57) pg. 6
Tip on using an electrical connector to attach a pushrod to a control horn. AERO MODELLER #685 Feb 1993 (v.58) pg. 13
Tip on using an electrical connector block as a source of push-rod connectors and wheel collets. AERO MODELLER #742 Sep 26 1997 (v.62) pg. 5
Modify a plastic airplane model to show the wing flaps in the down position. BOYS' LIFE Feb 2000 (v.90#2) pg. 55
Direct aileron driver system. A practical way to move ailerons with a servo. MODEL AVIATION Sep 1993 (v.19#9) pg. 120
Checklist of possible causes of control-surface flutter in model aircraft and some solutions. MODEL AVIATION Jan 1994 (v.20#1) pg. 6
Control-surface flutter. An effective solution to a serious problem in R/C model aircraft. MODEL AVIATION Oct 1994 (v.20#10) pg. 51
How to control flap and landing gear travel limits through the use of microswitches when using geared motors. MODEL AVIATION Mar 1995 (v.21#3) pg. 127
Pushrods and keepers. Advice on acceptable R/C pushrod construction, pushrod guides, fuselage exit options, etc. MODEL AVIATION Sep 1996 (v.22#9) pg. 60
How to install individual aileron servos. MODEL AVIATION Oct 1996 (v.22#10) pg. 68
Tip on cutting a crescent (curved) slot for an all-moving horizontal stabilizer. MODEL AVIATION Oct 1996 (v.22#10) pg. 78
Building effective dive flaps for model aircraft. MODEL AVIATION Nov 1996 (v.22#11) pg. 59
Tips on getting the proper geometry in all the mechanical linkages (control horns, push rods, servo arm, etc.) on RC model aerobatic aircraft. MODEL AVIATION Feb 1997 (v.23#2) pg. 69
Correction MODEL AVIATION Jul 1997 (v.23#7) pg. 83
Spoilers and air brakes for RC sailplanes. How to construct and fit them to both new and existing models. MODEL AVIATION Apr 1997 (v.23#4) pg. 76
Twin rudder linkage system using push-pull rod and no external horns. RADIO CONTROL MODELS & ELECTRONICS Jun 1990 (v.32#6) pg. 526
It's your throw. How to determine the amount of differential aileron control which can be obtained with various combinations of servo pushrod linkages. RADIO CONTROL MODELS & ELECTRONICS Feb 1992 (v.35#2) pg. 66
Alternative to conventional screw-on clevises for adjusting threaded pushrods. RADIO CONTROL MODELS & ELECTRONICS Apr 1992 (v.35#4) pg. 75
Tip on making a gauge to measure the amount of movement or throw which a rudder or elevator makes in relation to the fin or stabilizer. RADIO CONTROL MODELS & ELECTRONICS Jul 1992 (v.35#7) pg. 75
Control surface flutter. The aerodynamic causes and cures for this condition. RADIO CONTROL MODELS & ELECTRONICS Aug 1992 (v.35#8) pg. 82
How to avoid exponential differential. A look at the problems inherent in the geometry of mechanical aileron linkages. RADIO CONTROL MODELS & ELECTRONICS Feb 1993 (v.36#2) pg. 62
Tip on correct alignment when attaching a control horn to a sharply tapered control surface. RADIO CONTROL MODELS & ELECTRONICS Oct 1993 (v.36#10) pg. 72
Tip on inserting a threaded stud into inner snake cables. RADIO CONTROL MODELS & ELECTRONICS Oct 1993 (v.36#10) pg. 72
How to hook up R/C ailerons on aerobatic model aircraft. RADIO CONTROL MODELS & ELECTRONICS Apr 1994 (v.37#4) pg. 83
How to pin and hinge control surfaces (using mylar hinges) when building film-covered models. RADIO CONTROL MODELS & ELECTRONICS Jan 1995 (v.38#1) pg. 62
Correction RADIO CONTROL MODELS & ELECTRONICS Feb 1995 (v.38#2) pg. 7
Method for installing a "Y" shaped elevator pushrod where access is limited. RADIO CONTROL MODELS & ELECTRONICS Feb 1995 (v.38#2) pg. 30
How to make balsa pushrods that are equipped with threaded wire clevis rods at the ends. RADIO CONTROL MODELS & ELECTRONICS Mar 1995 (v.38#3) pg. 50
Tip on installing closed-loop control cables in model aircraft. RADIO CONTROL MODELS & ELECTRONICS Apr 1995 (v.38#4) pg. 74
Correction RADIO CONTROL MODELS & ELECTRONICS Jul 1995 (v.38#7) pg. 68
|